On this page below you will discover a good deal of brilliant expertise pertaining to How to Install a Bathtub.
Mounting a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard project. If the old tub is readily easily accessible, the job can move quickly; if you need to open up a wall surface to remove the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and set in the brand-new one. See to it you have actually certified yourself for the task and also fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to take into consideration employing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your bathroom if you have currently purchased a new tub and also don't need to alter the plan of your previous supply of water pipelines.
Your devices as well as material checklist must consist of the following:
Getting ready for the Setup
Firstly, the supporting frame supplied with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly problematic because of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing both wood boards under its feet, put the tub in the needed placement. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To install faucets, fit the bottom of the furthest versatile tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub needs to wait until the bathtub has been used at the very least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in location between the tap as well as the sink. Safeguard the faucet in place with the maker offered backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to fracture an inflexible seal, triggering the water to pass through the wall in between the bath and the tiling, leading to difficulties with wetness and possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealant can split fairly early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when looking around the search engines. Make sure you take the time to distribute this entry if you enjoyed reading it. Thanks for going through it.
Got a leak? Call!